PDA

View Full Version : HSD upper pillowball mounts ae86



1bad6
02-27-2014, 02:19 PM
Bought some HSD coilovers for my ta22 and cant use the upper pillow ball camber plates. 200$ for the two.

Might consider selling the whole ae86 front coilover setup. Just pm me or email dan_ouellet@yahoo.ca

http://i236.photobucket.com/albums/ff301/boosted_b20/IMG_1042_zpsf985792b.jpg
http://i236.photobucket.com/albums/ff301/boosted_b20/IMG_0966_zps9af1fe13.jpg

Brandon G
02-27-2014, 02:28 PM
Price for the whole setup? I actually quite like the HSD's on my Aristo.

76RA24
02-27-2014, 02:43 PM
why not modify and run all ae86 stuff in your TA22?

you have a build thread on here?

1bad6
02-27-2014, 06:23 PM
To sell the full suspension would be 1400
I never taught of making new top plates. I will have to look into that. I was going to sell these and get a set of t3's

Here is a link to my build thread
http://www.dorikaze.net/showthread.php?41999-My-RA24-build&p=462293#post462293

Jehuty77
02-27-2014, 06:34 PM
What are these plates for? an 86?

nolanator
02-27-2014, 06:49 PM
I wouldn't even bother making new strut tops. Just drill holes in your strut tower to suit the camber plates

1bad6
02-27-2014, 07:01 PM
Yeah these are for an AE86 corolla
I dont know if just making new holes would work, the strut seems offset from the center of the plate compared to the t3 camber plates for a ta22

oldskoolcool
02-28-2014, 07:49 AM
Post some pics, you can make it work and we will help!

Steve Groenink
02-28-2014, 12:00 PM
You only have to drill one hole in the strut tower, I ran ae86 Megan's on zongo without an issue

1bad6
02-28-2014, 01:57 PM
Post some pics, you can make it work and we will help!

http://i236.photobucket.com/albums/ff301/boosted_b20/20140226_145417_zps8f444029.jpg

b-rock
02-28-2014, 02:58 PM
Bonus caster, no?

nolanator
02-28-2014, 03:46 PM
Yea just drill the hole for that one stud. I had to do the same thing on my ae71

1bad6
02-28-2014, 05:34 PM
I might do that or i found some universal camber plates on ebay that you drill your own bolt patern. If i just redrill, should i be worried about the caster?

nolanator
02-28-2014, 07:55 PM
Caster should be the same if 2 of the 3 holes line up the same. Buying ebay universal plates would just be more work since you have to redrill 3 holes instead of one and then you have to measure out where you drill all those properly so you dont change the caster

Old 'Rollas
03-01-2014, 11:07 AM
Bonus caster, no?

QFT. Having the top of the strut moved back makes for more caster which is good!! Do it do it.


Caster should be the same if 2 of the 3 holes line up the same. Buying ebay universal plates would just be more work since you have to redrill 3 holes instead of one and then you have to measure out where you drill all those properly so you dont change the caster

I don't think you are talking about caster there. The strut mounts on older Toyotas is dead center, on the 86 they are offset and you can swap them side-to-side to gain some caster instead of shortening your tensions rods.

Brian
03-01-2014, 01:57 PM
Slot the hole in the tower and use a big washer underneath. Don't over think this stuff

1bad6
03-01-2014, 08:12 PM
fixed it!
got one of my buddys to machine me some new tops :)
http://i236.photobucket.com/albums/ff301/boosted_b20/20140301_223354_zpsc0a7e2a8.jpg
http://i236.photobucket.com/albums/ff301/boosted_b20/20140301_223442_zps3e0287b4.jpg
http://i236.photobucket.com/albums/ff301/boosted_b20/20140301_223520_zps2892acf3.jpg

b-rock
03-01-2014, 08:16 PM
F*ckin awesome.