Search:

Type: Posts; User: solid_state; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    26
    Views
    3,707

    I might be interested in the header. Got any...

    I might be interested in the header. Got any pics? How was it repaired?
  2. Replies
    38
    Views
    5,891

    2015 Update

    Time for my yearly update.

    The mango saw some action last year with my first autocross event!

    http://cobham.ca/Mango_Pics/JGB_7855.jpg

    And a few more events after that.
    ...
  3. Replies
    2
    Views
    648

    Yeah, I've already pulled both trans apart....

    Yeah, I've already pulled both trans apart. Swapped over the shift shafts and forks for the tailshaft housing that fits my car. The 20 spline shaft has a locknut on the rear bearing, and the 22...
  4. Replies
    2
    Views
    648

    T50 Mix and Match

    I'm going to be doing a 2T-C to 4AGE swap in my 72 TE27 mango. Mt original 2T-C engine has an early 20 spline T50 with a shifter housing that is set forward. The 4AGE has a later model T50 with a 22...
  5. Replies
    221
    Views
    19,568

    Nothing says game like a valve cover, covered in...

    Nothing says game like a valve cover, covered in American $100 bills...

    14256
  6. Replies
    97
    Views
    11,241

    No man, that's not a date code. Those numbers are...

    No man, that's not a date code. Those numbers are crankshaft rotation degrees before and after top dead center (BTDC). 20, 15, 10, 5 BTDC, 0, 5, 10 ATDC. They are timing marks that go along with the...
  7. Replies
    267
    Views
    49,829

    I checked back through your thread, but I didn't...

    I checked back through your thread, but I didn't see where you got your intercooler from... you know, just out of curiosity.
  8. well, it turns out our USD exchange rate sucks at...

    well, it turns out our USD exchange rate sucks at the moment. It's going to cost over $300 with shipping etc.. for a $150 manifold. I'm being cheap at the moment, but I might not have any other...
  9. Not my link, it's straight off the googles. maybe...

    Not my link, it's straight off the googles. maybe they like bird food?
  10. WTB: 2/3tc short runner, side draught intake manifold

    Like the title says, I'm looking for a 2/3tc short runner mikuni style intake manifold for side draught carbs.

    For reference:...
  11. Replies
    42
    Views
    4,136

    I'm sure you already know there's a few places...

    I'm sure you already know there's a few places that will do low volume PCBs, but have you tried OSH Park? https://oshpark.com/
    Their build quality and turn around time is great. I think the prices...
  12. So if you did a 5spd swap from auto to manual, I...

    So if you did a 5spd swap from auto to manual, I assume you installed a clutch pedal and bracket etc..? It sounds like maybe you have a pinched or broken wire under the dash where you installed the...
  13. Replies
    9
    Views
    656

    I figure I'd post a follow up to this if anyone...

    I figure I'd post a follow up to this if anyone is interested. I opened up the wideband to find nothing obviously wrong. My initial observations were that the PCBs were probably the cheapest quality...
  14. Replies
    8
    Views
    1,233

    Well, after I said I wasn't going to do it...

    Well, after I said I wasn't going to do it ghetto, I got carried away and did this. I drilled a hole in a spare banjo bolt and then welded a air fitting onto it. The only gauge I had was from an AC...
  15. Replies
    8
    Views
    1,233

    Hah, yeah I already tried to go the ghetto route,...

    Hah, yeah I already tried to go the ghetto route, but I couldn't make a setup that I could measure the pressure and actually drive the truck at the same time. Sometimes I hate my truck, but I'm not...
  16. Replies
    8
    Views
    1,233

    Fuel pressure tester SST

    Does anybody local have a fuel pressure tester fitting I can borrow for a few hours? My manual says it's SST 09268?45012 which looks like a banjo fitting with an extended bolt to double up two...
  17. Replies
    9
    Views
    656

    Well, I'll crack this one open and have a look. I...

    Well, I'll crack this one open and have a look. I was more or less looking for comments on build quality and reliability.
  18. I have a small assortment of pilot jets and 1...

    I have a small assortment of pilot jets and 1 size of main air jet. I'm looking to lean out the mains. Maybe we can trades?
  19. Replies
    9
    Views
    656

    MTX-L Problems?

    I've been running an innovate MTX-L wideband for the last 1.5? years. The other day it just quit. No display, nothing. I disconnected the O2 sensor and checked all the wiring but still no action....
  20. Replies
    0
    Views
    147

    WTB: 72 Mango Tail Light Trim

    Kind of a long shot, but I really need the tail light trim. Maybe someone has one in their stash?
    I'd also be interested in any other interior/exterior trim pieces.

    Thanks

    13699
  21. Replies
    38
    Views
    5,891

    Thanks! It's a Toyota paint code but not from the...

    Thanks! It's a Toyota paint code but not from the same model year. I'd have to check the can to be sure of which year etc... I picked it from a paint chip, which looked less yellow at the time.
  22. Replies
    38
    Views
    5,891

    Well, I went ahead and did a thing... 13687 ...

    Well, I went ahead and did a thing...

    13687

    13688

    13689

    It turned out not too bad. Now that it's painted, its easy to see where I could have spent more time on the doors and fenders....
  23. Replies
    9
    Views
    397

    I PM'ed you some contact info. Good luck.

    I PM'ed you some contact info. Good luck.
  24. Replies
    9
    Views
    397

    I had a tough time finding a windshield for my...

    I had a tough time finding a windshield for my mango. I ended up finding a guy on 3tc garage who had a stash of reproductions. He was very reluctant to ship and I had to get it brought back from...
  25. Replies
    115
    Views
    13,258

    Cut off the mounting tab and weld it back in the...

    Cut off the mounting tab and weld it back in the right position?
Results 1 to 25 of 98
Page 1 of 4 1 2 3 4