Search:

Type: Posts; User: Answ3r; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Thread: DK Dead?

    by Answ3r
    Replies
    83
    Views
    10,029

    I'm pretty sure facebook is the reason for 80% of...

    I'm pretty sure facebook is the reason for 80% of the slow down on the forum. The other 20% is the fact that these cars are now very rare and people what 3-400hp anyways so they move onto something...
  2. Replies
    29
    Views
    4,963

    The JB weld was a double measure to make sure I...

    The JB weld was a double measure to make sure I don't get pinholes leak through the actual weld. I wouldn't trust the JB to hold a bung in a pan alone...
  3. Replies
    19
    Views
    1,163

    Bumping a SUPER OLD thread back from the dead,...

    Bumping a SUPER OLD thread back from the dead, but anyone still have a set of those around or pictures ?

    Thanks :)
  4. Replies
    29
    Views
    4,963

    14917 Actually it's a oil cooler plate from a...

    14917
    Actually it's a oil cooler plate from a fwd redtop I think...
  5. Replies
    29
    Views
    4,963

    I'm running the stock oil cooler plate and tapped...

    I'm running the stock oil cooler plate and tapped an 1/8 NPT to -3AN fitting in the side to feed the turbo. No issues here for a long time.

    You can slightly shim the oil cooler bypass spring or...
  6. Replies
    29
    Views
    4,963

    Intercooler will keep intake temps lower and thus...

    Intercooler will keep intake temps lower and thus reliability should be better. For the ms3 I can send you my map if youd like, dyno tuned. Id remove 1 degree timing since you have stock pistons and...
  7. Replies
    29
    Views
    4,963

    Been there, done that. Ran for 2 summer and...

    Been there, done that. Ran for 2 summer and cracked rings lands on cylinder #2 haha.

    Here's the BEST recipe for it to work, while keeping it simple. But never try running more than 7 psi, it will...
  8. Replies
    4
    Views
    459

    Spark table you can use pretty much the same. ...

    Spark table you can use pretty much the same.

    Fueling, I don't even know how SDS calculates, I'd guess you'll have to start from scratch.
  9. Thread: Elizabeth

    by Answ3r
    Replies
    289
    Views
    57,888

    Picture of said ebrake mod ?

    Picture of said ebrake mod ?
  10. You can use smallport rings IIRC on GZE pistons. ...

    You can use smallport rings IIRC on GZE pistons.

    You did not reply concerning the bumper.

    Thanks !
  11. I might be interested in the front bumper only if...

    I might be interested in the front bumper only if you can ship.
  12. Replies
    6
    Views
    559

    Don't sweat about it. This was probably a...

    Don't sweat about it. This was probably a remaining burr. You can smooth that out with some really fine sandpaper and wd40, works good.
  13. Replies
    830
    Views
    92,283

    Want more hp, raise boost ? I mean you have it...

    Want more hp, raise boost ? I mean you have it all except huge injector and exhaust which you'd need anyways.
  14. Replies
    10
    Views
    983

    I like ProForm "euro" one. It's beige and like...

    I like ProForm "euro" one. It's beige and like stock. http://www.proformproducts.com/en/products/detail/?id=22&category=4
  15. Look good. Take a picture outside.

    Look good. Take a picture outside.
  16. Replies
    1,635
    Views
    275,337

    I emailed Summer brothers racing for fun to see...

    I emailed Summer brothers racing for fun to see how much a set of heavy duty axle would cost. I asked for a group buy too. Got this:

    Yes, we can make you the Toyota axles. Are you racing?
    How...
  17. Replies
    830
    Views
    92,283

    If you are really carefull with a big file,...

    If you are really carefull with a big file, marking blue and a dial indicator you can make it pretty good. I installed an lsd for a friend and at first it had like >.005" runout, and got it down to...
  18. Replies
    1,635
    Views
    275,337

    Also trying new oem axles might work longer than...

    Also trying new oem axles might work longer than tired 25 years old ones lol
  19. Replies
    830
    Views
    92,283

    I set my preload to "pretty tight" for old...

    I set my preload to "pretty tight" for old bearing and "god it feels too tight" for new ones. As for the side bearings, I set the preload at "maximum ****ing tight". Backlash I try and get .006", if...
  20. Replies
    830
    Views
    92,283

    I've been thinking about it all day and it makes...

    I've been thinking about it all day and it makes do sense to crush shim stock with pure compression. Even if they were wild steel... I'll do some calculation later. Something seizing/spinning could...
  21. Replies
    830
    Views
    92,283

    Yeah I machined those on a CNC so making smaller...

    Yeah I machined those on a CNC so making smaller bevels would be easy but I feel like there might be something else to your failure.

    If the driveshaft binding in the suspension travel ?
  22. Replies
    830
    Views
    92,283

    Holly **** ! First time I've seen crushed shim...

    Holly **** ! First time I've seen crushed shim stock ! Sure the solid spacer could be made with a smaller chamfer, it's mostly there to make for a nice part without a sharp edge.

    Wonder how...
  23. It's going to end up costing a million an produce...

    It's going to end up costing a million an produce an extra 5hp. I don't suggest you do it.
  24. Replies
    539
    Views
    69,481

    Azenis are really big plus you have a 195/60 ;)

    Azenis are really big plus you have a 195/60 ;)
  25. Replies
    124
    Views
    23,865

    2 sets of F20C mounts and 3 sets of big brake...

    2 sets of F20C mounts and 3 sets of big brake mounts coming in...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4