Search:

Type: Posts; User: YYZ78; Keyword(s):

Page 1 of 13 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    708

    I should add that I don't have any grinding...

    I should add that I don't have any grinding issues....shifts nice; maybe just get the input bearings replaced and skip the whole rebuild...?
  2. Replies
    4
    Views
    708

    W58 Rebuilding in Toronto/Ontario ?

    Getting some noise when trans is all warmed up in the Cressy....goes away when clutch in, so thinking its input shaft bearing.

    If it's only there sometimes....how urgent is it?

    Thinking this...
  3. Replies
    1
    Views
    357

    whoa....350 for a w58 these days....last 2 I got...

    whoa....350 for a w58 these days....last 2 I got here in Toronto were only 150 bucks!
  4. Replies
    14
    Views
    2,187

    Master cylinder Bore of Toyota 4x4 trucks with...

    Master cylinder Bore of Toyota 4x4 trucks with s12+8 4 pot calipers is 7/8, 240z master cylinder is 7/8

    Total Piston area of Stock 2 piston calipers (54mm bore) = 9156 mm sq
    Total Piston area of...
  5. Replies
    14
    Views
    2,187

    Not just thrown together.....pretty common swap...

    Not just thrown together.....pretty common swap with 240z guys....piston area is only like a 4% increase....rotors are same diameter as stock
    With the warm weather recently I got out to bed the...
  6. Replies
    14
    Views
    2,187

    Pedal is firm, no air bubbles coming from front...

    Pedal is firm, no air bubbles coming from front calipers so pretty sure they are bled fine....but I will double check.
  7. Replies
    14
    Views
    2,187

    Could it be the metering valve in my combination...

    Could it be the metering valve in my combination valve is stuck/gone bad? I read that if they get stuck they can limit pressure/power of front brakes.
    Any major issues if I just delete the metering...
  8. Replies
    14
    Views
    2,187

    I don't think the new calipers were that much of...

    I don't think the new calipers were that much of an increase in combined piston area to warrant an uprated master cylinder size, but I could be wrong. I have the rears locking and there is lots of...
  9. Replies
    14
    Views
    2,187

    They are new rotors on the front, but I wiped em...

    They are new rotors on the front, but I wiped em down with brake cleaner before I installed them.
  10. Replies
    14
    Views
    2,187

    Front brakes won't lock up

    I just did the 4 pot s12+8 80s 4x4 toyota truck caliper and x7 vented rotor swap on my x3 cressida (a common swap 240z guys do..). Haven't had a chance to bed the brakes fully yet, but I can't get...
  11. Replies
    13
    Views
    1,113

    Just as a side note. When I converted my x3 from...

    Just as a side note. When I converted my x3 from auto to manual, I had a problem with the firewall where the clutch master mounted flexing when I depressed the clutch. I reinforced the area and pedal...
  12. Replies
    13
    Views
    1,113

    I had thought of this. I have a feeling that...

    I had thought of this. I have a feeling that spring is going to be a bitch to get on/off though with the pedal still in the car... so I'm leaving it as a last resort type situation.[/QUOTE]

    Good...
  13. Replies
    13
    Views
    1,113

    Could also be the master or slave cylinder...

    Could also be the master or slave cylinder leaking....sometimes the leak is contained internally so its hard to see. If removing spring and or adjusting doesn't work maybe try rebuild the master and...
  14. Replies
    13
    Views
    1,113

    Take off the return spring and see if it returns...

    Take off the return spring and see if it returns without it?
    If it does, then you know its something to do with that spring/centering, etc.
  15. Replies
    38
    Views
    11,633

    I think he means did you actually calculate/ use...

    I think he means did you actually calculate/ use geometry to determine the mounting height?
  16. Thread: jz in my pants

    by YYZ78
    Replies
    304
    Views
    56,075

    Curious what you'll be doing for chassis...

    Curious what you'll be doing for chassis stiffening....frame connectors and torque boxes like some of the 86 stuff done in Japan.
    I want to stiffen up my jzx32
  17. such a nice car....hate to say it but needs some...

    such a nice car....hate to say it but needs some proper wheels though....she's begging for them
  18. Replies
    14
    Views
    1,748

    w58

    w58
  19. Replies
    14
    Views
    1,748

    Just met 2 guys with starlets this past weekend...

    Just met 2 guys with starlets this past weekend at the OIRC meet in Scarborough
    Both had 3sgte in em....I can only imagine how quick they are
  20. Great job...looks fantastic!

    Great job...looks fantastic!
  21. Replies
    1,354
    Views
    211,314

    Sticky: love it wingless...waaaay better. Such nice...

    love it wingless...waaaay better. Such nice subtle style with the stock arches and streets. Please leave it wingless :smilewinkgrin:
  22. So, I reinstalled the old timing belt with the...

    So, I reinstalled the old timing belt with the new tensioner and pulley...fired it up and the belt tracked perfectly....
    So it must just be the belt is slightly miscut or something...?
    At least I...
  23. Timing Belt moving side to side on cam gears

    Changed my timing belt and water pump, pulley tensioner on my 2jzge vvti,

    Belt moves side to side slightly....is this normal or a problem?

    ...
  24. Replies
    4
    Views
    1,556

    ^^^this

    ^^^this
  25. Replies
    1,354
    Views
    211,314

    Sticky: my X3 is rid of dreaded Steering box....very...

    my X3 is rid of dreaded Steering box....very excited ;)
    14399
Results 1 to 25 of 307
Page 1 of 13 1 2 3 4