Results 1 to 6 of 6

Thread: AE86 starter contacts: how to do them and part numbers

  1. #1
    Join Date
    Aug 2004
    Location
    86tuning, Vancouver
    Posts
    8,869

    AE86 starter contacts: how to do them and part numbers

    Well, this question comes up quite often:

    Q: my starter makes a single click noise, but doesn't turn the engine over. My battery voltage is over 12.5v
    A: If your battery is good, then your starter contacts are likely worn out.

    Q: How do I change the contacts?
    A: It's pretty simple to do, the hardest part is taking the starter out. There's many methods to take the starter out. Illustrated here is the "remove exhaust manifold method" where you undo the exhaust manifold, slide it out about an inch, then pull the starter out the back.

    First things first. You'll need to access the underside of the car. So you'll need a jack and jackstands.

    Before you begin, disconnect the battery negative terminal

    Start with removing the 3 nuts holding the exhaust manifold to the front pipe, plus the nut that holds the brace in place. You get one from above, and the other 3 from below, using a 14mm plus long extension.


    Use a 24mm socket and large ratchet to remove the EGR pipe "banjo bolt"


    Next remove the manifold heat shield to access the manifold nuts and bolts. There are four 10mm nuts to hold the heatshield on. Then there are five 14mm nuts/bolts: 2 nuts, 3 bolts hold the manifold to the head.


    Once the manifold nuts are undone, you get to remove or pry back the upper manifold about an inch.

    There are two 14mm bolts that hold the starter to the transmission. You can reach them from either above or below. Take those off. Then turn the starter around until you can undo the 12mm nut that holds the fat wire from the battery onto the starter. Also, unplug the little wire from the starter. It may be helpful to remove the oil filter to get more space.

    Once those are all undone, you can take the starter out from the backside.


    Phew. That was hard work. Take a 5 minute break, and then put your starter into a bench vise, and take the heatshield off (10mm bolt) and remove the other terminal wire (12mm nut)



    Remove the endcap from the starter. Most use 8mm bolts, some use 7mm bolts.


    After taking off the cap, the plunger comes out, and you expose the contacts themselves.


    Take a good look, usually only the one terminal is worn out, and the other might be re-useable. But it's a really good idea to change both.

    Carefully remove the starter contacts from the starter. You can hold the inside with a 13mm wrench while you carefully undo the 14mm outside. I use a 3/8" impact wrench, you can use a 14mm wrench or socket, whatever you like.

    With the contacts on the table, you can see in the pix what's good and what's not. The dead contact has a deep groove worn into it.


    Here's a pic of the plunger before cleaning it up with a wire wheel. And another pic of the contacts themselves. Write down the part number for the contact, as it's a special order item from most dealerships.



    Carefully wire wheel the plunger contact to clean it up a bit. Easy does it, no need to be harsh, just a gentle brushing with the wire wheel. Note that there is very little material removed, but all the carbon tracking is gone.


    Next, install the new contacts back into the starter. The new, improved, wider "previa" contact replaces the worn out one. Use a 13mm wrench to hold the "bolt-head" in place to keep the contact from twisting. Be sure that the contact sits square in it's spot, without being twisted to one side.

    Re-install the fat motor wire to the one starter contact. Be sure all the plastic bits, curved washer, and O-ring are in place.

    Put the plunger back in, then the endcap, and the outer cap with three screws. Re-install the heatshield, then it's time to test the starter operation. You'll need an SST which is super easy to make from a couple non-insulated spade terminals and a short bit of wire.


    Take your regular jumper cables, and put the positive clamp on the starter terminal, and the negative clamp on the starter frame. Your SST plugs into the small terminal on the starter.


    Once you're sure you have the connections right, you can brush the SST against the starter terminal to apply +12V to the small connector on the starter. The starter will lurch (unless it's firmly held in a vise as shown) and the starter gear will spit out about an inch and spin up simultaneously. Keep your fingers clear!


    Resting position, no power applied


    Starting position, with +12V applied


    Once you've tested your starter, carefully disconnect your jumper cables etc, and then put your starter back into the car.

    Installation is the reverse of removal procedure :cool:
    Last edited by celica-fiend; 11-28-2013 at 09:48 AM.
    - Brian


  2. #2
    Join Date
    Aug 2004
    Location
    86tuning, Vancouver
    Posts
    8,869
    If you've done this repair before, you can expect to take around 2 to 3 hours total... it really depends on how long it takes to get the fricken starter out of it's hidey hole. The actual starter contact replacement is about 15 minutes, just cruising...

    Sure beats removing and replacing the starter, plus paying $199 for a rebuilt one, when genuine repair parts cost something like 30-40 bux... plus whatever gaskets you choose to replace.


    Other ways to take the starter out include removing the oil filter and the oil filter base, then taking the starter out from the front.

    Not a lot of room to do it this way, especially if you've got power steering Possible, but not fun.

    Oh, if you have headers on your car, then changing the starter contacts are super easy, you don't have to move the headers at all, the starter just comes straight out the backside.
    Last edited by Brian; 12-27-2005 at 02:05 AM.
    - Brian


  3. #3
    Join Date
    Jul 2004
    Location
    Vancouver, BC
    Posts
    2,017
    That demo car looks hawt
    Team おなに

    Motor Village Crew unite!

  4. #4
    Join Date
    Mar 2004
    Posts
    1,341
    Excellent writeup Brian.

    This will now be moved to the Reference Section.

    No further posts please!

    Thank you.

    Admin/Mod Team.
    A thief broke into my house last night...He started searching for money so I woke up and searched with him

  5. #5
    narfy's Avatar
    narfy is offline gigidy gigidy... ooo right!!
    Join Date
    Mar 2004
    Location
    Regency Toyota
    Posts
    9,438
    if memory serves....
    28226-72010
    28226-64110

    one of each of these kits...

    there's a write-up including parts in the tech reference section as well...
    VZN185 - 32" BFG AT, OME suspension, ARB bumper, lightforce lights, TRD trans cooler, TRD exhaust, AMT sliders, budbuilt plates...
    ZN6 - stock with HIDs and LEDs...
    fng@regencyauto.com

  6. #6
    Join Date
    Nov 2004
    Location
    Edmonton, Alberta
    Posts
    5,276
    AE86 Starter Component Parts (Order/use what you need):

    Battery Side Contact: 28226-72080 (28226-64110 can be used as well IIRC).
    Motor Side Contact: 28226-72010
    Plunger: 28235-35080
    Plunger Spring: 28165-26040
    Plunger Spring Ball: 90099-12009
    End Cover: 28159-10040
    End Cover Gasket: 28175-10040
    End Cover Bolts: 90099-04473
    Wiring Clamp: 28169-10040

    Hope this helps anyone looking for other components when in there.

    Jeff

    2011 GSE20 Lexus IS350 6MT F-Sport with LSD
    2005 NCP13 Toyota Yaris RS 5MT Hatchback
    1993 TCR10 Team Mondor Toyota Previa GT-S RM 5MT Studded Ice Race Van
    1986 AE86 Toyota Corolla GT-S 5MT Supercharged

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •