Page 39 of 41 FirstFirst ... 293132333435363738394041 LastLast
Results 761 to 780 of 806

Thread: Project Silly Celica.....*it runs, vid page11*

  1. #761
    Join Date
    May 2006
    Location
    Campbell River
    Posts
    3,156
    You are good at 1UZs
    1JZ 1984 Celica GTS
    1UZ 1981 Corolla sedan
    ? 1972 Celica race car

  2. #762
    Join Date
    Jul 2003
    Location
    Lethbridge Alberta
    Posts
    4,475
    Went to the track this weekend to see how the bugs shake out!

    10.400@142.64mph with a 1.83 60'




    Not too bad at all considering it's a turbo, Stick shift, low profile radial car set up for corner carving lol there's still lots more left in it. That was on 21psi. So I'll head back in a couple weeks, play with the shocks a little more and throw some more boost at it and hopefully attain my goal of 9.99@150mph
    Last edited by Steve Groenink; 05-30-2016 at 06:07 PM.
    Owned too many different modified toyotas to list LOL


  3. #763
    Join Date
    May 2006
    Location
    Edmonton
    Posts
    113
    I have nothing to add, other than to say this car is really something special. I love it!
    Oh, and you posted the same burnout video, perhaps you meant to post track video?
    I hope said video is in car. I bet it makes amazing sounds on the inside too

  4. #764
    Join Date
    Jul 2003
    Location
    Lethbridge Alberta
    Posts
    4,475
    Thanks I think I fixed the video now?
    Owned too many different modified toyotas to list LOL


  5. #765
    Join Date
    Jul 2005
    Location
    Kelowna BC
    Posts
    110
    Hey Steve,
    I would love to see a picture of your Pedal Box installation!
    Is that possible?
    Thank You,
    Adam
    Josh Danish is a Scammer

  6. #766
    Join Date
    Jul 2003
    Location
    Lethbridge Alberta
    Posts
    4,475
    You could say things have gotten a little serious....





    Owned too many different modified toyotas to list LOL


  7. #767
    Join Date
    Nov 2012
    Location
    Brampton, Ontario
    Posts
    1,488
    Is that an auto? Did this always have an auto?

  8. #768
    Join Date
    Jul 2003
    Location
    Lethbridge Alberta
    Posts
    4,475
    Quote Originally Posted by Sparkie View Post
    Is that an auto? Did this always have an auto?
    Will be an auto now but previously had a t56 magnum 6spd in it
    Owned too many different modified toyotas to list LOL


  9. #769
    Join Date
    May 2006
    Location
    Campbell River
    Posts
    3,156
    He lives his life 1/4 mile at a time. As short a time as possible.
    1JZ 1984 Celica GTS
    1UZ 1981 Corolla sedan
    ? 1972 Celica race car

  10. #770
    Join Date
    Jul 2004
    Location
    Calgary
    Posts
    2,532
    Do you have plans for the T56? or did that get blown up LoL
    Bryan
    DK Moderator




  11. #771
    Join Date
    Feb 2009
    Location
    East Van reppin'
    Posts
    3,326
    "celica"

    In Toyota, we rust.

  12. #772
    Join Date
    Apr 2010
    Location
    Sylvan Lake Alberta
    Posts
    267
    well Steve, I've always felt like a bit of an outcast being on this board with a drag car, now i o have company for sure.
    85Sr5 3RZ+TH400+8.8 TO B CONTINUED

  13. #773
    Join Date
    Aug 2008
    Location
    London ON
    Posts
    1,621
    Things have gotten super srs

    1991 Tercel 4A-GEsmallport RIP 09/02/2011 - - 1993 Supra.
    05 IS300 Daily

  14. #774
    Join Date
    Jul 2003
    Location
    Lethbridge Alberta
    Posts
    4,475
    Quote Originally Posted by Old 'Rollas View Post
    Do you have plans for the T56? or did that get blown up LoL
    Sold the trans itself, still have the adapter/clutch/flywheel setup for it though, along with the 1uz which are both for sale but I just haven't had the time to actually advertise them lol
    Owned too many different modified toyotas to list LOL


  15. #775
    Join Date
    Jul 2003
    Location
    Lethbridge Alberta
    Posts
    4,475
    A few updates

    Fabricated 9" housing with four link brackets and back brace, narrowed and line bar'd ready for some paint



    Front suspension all finished up


    Seats mounted



    Removeable Driveshaft loop installed, temporary body mounts made so it has some to index back onto after I remove it to finish the top side of the cage welding



    Rear suspension structure and tubing started yesterday




    A small yet important detail! This hole is in the dash bar, fully sleeved and welded/dressed. This allows me to run wiring for say headlights/signal lights etc down through the strut tubes and out to the front to keep as many wires as possible hidden



    Should be off the table and on the ground in the next couple weeks for final welding and then chassis certification!
    Owned too many different modified toyotas to list LOL


  16. #776
    Join Date
    Jul 2003
    Location
    Lethbridge Alberta
    Posts
    4,475
    First floor panel installed



    Door hinges done




    Chassis/cage is done minus the passenger door bars.


    Original dashboard will work great, steering column mounted


    Rear suspension and cage is done

    Owned too many different modified toyotas to list LOL


  17. #777
    Join Date
    Apr 2010
    Location
    Sylvan Lake Alberta
    Posts
    267
    Sweeeeeet
    85Sr5 3RZ+TH400+8.8 TO B CONTINUED

  18. #778
    Join Date
    Nov 2012
    Location
    Brampton, Ontario
    Posts
    1,488
    What engine powers this now? It's still going to be turbo, guessing from the front exit manifold.

  19. #779
    Join Date
    Jul 2003
    Location
    Lethbridge Alberta
    Posts
    4,475
    Quote Originally Posted by Sparkie View Post
    What engine powers this now? It's still going to be turbo, guessing from the front exit manifold.
    big single turbo (built by Scremin) on an aluminum LS this round
    Owned too many different modified toyotas to list LOL


  20. #780
    Join Date
    Jul 2003
    Location
    Lethbridge Alberta
    Posts
    4,475
    Firewall progress


    Drivers steel floor done


    Ignore the ugly ass grinding pattern on the floor where the Tilton pedal box mounts, it's an optical illusion in the photo. Note that the firewall panels use 6-32 button head cap screws to be retained.


    And my new billet 88mm goodness custom made by Scremin! This things gonna be a monster!
    Owned too many different modified toyotas to list LOL


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •