Page 3 of 3 FirstFirst 123
Results 41 to 50 of 50

Thread: Serendipity's comprehensive AE86 J160 swap

  1. #41
    Join Date
    Nov 2010
    Location
    Beyond the Sun
    Posts
    1,295
    Quote Originally Posted by davew View Post
    Nice write up! Are you going to have to fab a custom exhaust header to over come clearance issues?
    davew
    Hi Dave. Thanks a lot. Which clearance issues? Any AE86 header fits.

  2. #42
    Join Date
    Nov 2006
    Location
    South Lyon Michigan
    Posts
    107
    I thought with a larger trans you would have to off-set the exhaust system?
    Davew

  3. #43
    Join Date
    Nov 2010
    Location
    Beyond the Sun
    Posts
    1,295
    Quote Originally Posted by davew View Post
    I thought with a larger trans you would have to off-set the exhaust system?
    Davew
    The exhaust routes outside the steering column. We haven’t modified the location of the steering column, therefore, we should have no problems using an exhaust designed for a LHD AE86.

    You’re likely mixing up fitment issues between LHD and RHD exhaust manifolds. I know from my communication with TODA that their RHD manifold will NOT fit LHD. Moreover, OBX LHD knockoffs are notoriously poorly fabricated and need to be modified to fit properly. A DK member who bought two of the told me that they both fit differently and had interference problems. Lol

  4. #44
    Join Date
    Nov 2010
    Location
    Beyond the Sun
    Posts
    1,295
    Step 6: Wiring

    The new ECU harness is set up for a GTS, but as my baby was born an SR5, we had to move a couple pins to match.
    Click image for larger version. 

Name:	Main adjustments 1.JPG 
Views:	7 
Size:	159.8 KB 
ID:	15889Click image for larger version. 

Name:	Main Adjustments 2.JPG 
Views:	7 
Size:	405.7 KB 
ID:	15888

    We had also piggy backed a new pin and plug for the alternator with my SQ order. Time to refresh it.
    Click image for larger version. 

Name:	Alternator re-pin.JPG 
Views:	8 
Size:	344.6 KB 
ID:	15891Click image for larger version. 

Name:	Alternator re-pin 2.JPG 
Views:	6 
Size:	396.1 KB 
ID:	15890

    Double checking the SPAL electric fan wiring. All good in the hood.
    Click image for larger version. 

Name:	Spal wiring 2.JPG 
Views:	6 
Size:	455.7 KB 
ID:	15892Click image for larger version. 

Name:	Spal wiring 1.JPG 
Views:	6 
Size:	441.5 KB 
ID:	15893Click image for larger version. 

Name:	Spal Wiring 3.JPG 
Views:	6 
Size:	430.3 KB 
ID:	15894

    There were a few more wires to hook up for the ECU.
    Click image for larger version. 

Name:	Additional pins 1.JPG 
Views:	7 
Size:	406.6 KB 
ID:	15896Click image for larger version. 

Name:	Additional pins 4.JPG 
Views:	7 
Size:	454.6 KB 
ID:	15895

    There’s also a plug for a CAN BUS, should we decide to add/use a data logger.
    Click image for larger version. 

Name:	Additional pins 2.JPG 
Views:	5 
Size:	467.3 KB 
ID:	15897

    Double checked the 12V positive line all the way back to the fuel pump. A-OK.

    Picked up a Toyota harness plug with pins for the reverse lights from Tweaked.

    AEM Wideband setup.
    Click image for larger version. 

Name:	AEM 1.JPG 
Views:	6 
Size:	388.4 KB 
ID:	15898Click image for larger version. 

Name:	AEM 2.JPG 
Views:	7 
Size:	316.9 KB 
ID:	15909

    Grounds Grounds Grounds

    An often overlooked part of a refresh or new ECU setup is replacing the grounds. We don’t want to waste any dyno time chasing after things we should have done beforehand.
    Click image for larger version. 

Name:	Engine & Trans Ground.JPG 
Views:	7 
Size:	501.0 KB 
ID:	15911Click image for larger version. 

Name:	Greasy Grounds 1.JPG 
Views:	7 
Size:	357.6 KB 
ID:	15908Click image for larger version. 

Name:	Greasy Grounds 2.JPG 
Views:	7 
Size:	347.6 KB 
ID:	15907

    Battery Ground: 1 gauge with Pico adhesive heat shrink, sealing the soldered union from corrosion. Replaced the OEM M6 bolt with a plated M8.
    Click image for larger version. 

Name:	Battery Ground 1.JPG 
Views:	6 
Size:	333.3 KB 
ID:	15902Click image for larger version. 

Name:	Battery Ground 2.JPG 
Views:	5 
Size:	347.5 KB 
ID:	15901Click image for larger version. 

Name:	Battery Ground 3.JPG 
Views:	5 
Size:	382.5 KB 
ID:	15900Click image for larger version. 

Name:	Battery Ground 4.JPG 
Views:	6 
Size:	325.8 KB 
ID:	15899

    Engine Ground: 2 gauge with plated M8 bolt into the frame rail.
    Click image for larger version. 

Name:	Engine Ground 1.JPG 
Views:	6 
Size:	408.7 KB 
ID:	15903

    Intake and trans grounds: 10 gauge with plated M8 bolts.
    Click image for larger version. 

Name:	Intake ground 1.JPG 
Views:	6 
Size:	342.0 KB 
ID:	15904Click image for larger version. 

Name:	Intake ground 2.JPG 
Views:	7 
Size:	429.6 KB 
ID:	15905Click image for larger version. 

Name:	Intake ground 3.JPG 
Views:	6 
Size:	408.1 KB 
ID:	15906

    We're almost ready to crank her over.
    Click image for larger version. 

Name:	AE86 Haltech.JPG 
Views:	8 
Size:	430.5 KB 
ID:	15910
    Last edited by Serendipity; 11-23-2019 at 03:13 PM.

  5. #45
    Join Date
    Nov 2010
    Location
    Beyond the Sun
    Posts
    1,295
    Step 7: Clutch hydraulics

    Not that interesting of a step, but a necessary one.

    Rebuilding the slave master.
    Click image for larger version. 

Name:	Slave Rebuild.JPG 
Views:	7 
Size:	483.1 KB 
ID:	15912

    New clutch soft line.
    Click image for larger version. 

Name:	Clutch Softline.JPG 
Views:	7 
Size:	322.2 KB 
ID:	15913
    Last edited by Serendipity; 11-23-2019 at 03:31 PM.

  6. #46
    Join Date
    Nov 2010
    Location
    Beyond the Sun
    Posts
    1,295
    Step 8: Intake filtration

    Can't run an engine without a proper air filter.

  7. #47
    Join Date
    Nov 2010
    Location
    Beyond the Sun
    Posts
    1,295
    CHAPTER 5: FINAL STEPS

    Step 1: Shifter
    Step 2: Driveshaft
    Step 3: It lives!
    Step 4: Tuning

  8. #48
    Join Date
    Nov 2010
    Location
    Beyond the Sun
    Posts
    1,295
    Step 1: Shifter

    C’s short shifter in place
    Click image for larger version. 

Name:	C's Shifter J160.JPG 
Views:	6 
Size:	484.9 KB 
ID:	15914

    See how they run…see how they run..
    Last edited by Serendipity; 11-23-2019 at 03:48 PM.

  9. #49
    Join Date
    Nov 2010
    Location
    Beyond the Sun
    Posts
    1,295
    Step 2: Driveshaft

    Warren has an impressive collection of crusty old shafts. Which one of these princesses will fit the glass shoe?
    Click image for larger version. 

Name:	Driveshaft Mugshot.JPG 
Views:	5 
Size:	372.3 KB 
ID:	15915Click image for larger version. 

Name:	Slip Yoke 4.JPG 
Views:	5 
Size:	321.2 KB 
ID:	15920Click image for larger version. 

Name:	Slip Yoke 2.JPG 
Views:	4 
Size:	342.0 KB 
ID:	15919Click image for larger version. 

Name:	Slip Yoke 3.JPG 
Views:	4 
Size:	357.2 KB 
ID:	15918

    Our Cinderella is an auto 3TC ('80-'83) propeller shaft/front shaft. It fit perfectly with the GTS rear end and rear shaft! Well well well…
    Click image for larger version. 

Name:	3TC Driveshaft.JPG 
Views:	7 
Size:	453.4 KB 
ID:	15916

    Now to send it to Island Torque Converter to have the propeller shaft built with the new slip and weld yokes.
    Click image for larger version. 

Name:	Slip Yoke 1.JPG 
Views:	5 
Size:	354.8 KB 
ID:	15917

    Back from Island Torque Converter with a Spicer serviceable u-joint and both halves balanced together. The intermedate shaft was already rebuilt a short time ago. The painted yellow marks tell us how to properly phase the driveshaft.
    Click image for larger version. 

Name:	Driveshaft 1.JPG 
Views:	4 
Size:	450.1 KB 
ID:	15925Click image for larger version. 

Name:	Driveshaft 2.JPG 
Views:	5 
Size:	433.6 KB 
ID:	15924

    Now to replace the hanger bearing with the one from my T50 setup. Goodbye hammer...
    Click image for larger version. 

Name:	Driveshaft 3.JPG 
Views:	4 
Size:	359.3 KB 
ID:	15923

    Now to paint it so it looks the part. Black goes with everything.
    Click image for larger version. 

Name:	Driveshaft 4.JPG 
Views:	5 
Size:	454.6 KB 
ID:	15926Click image for larger version. 

Name:	Driveshaft 5.JPG 
Views:	4 
Size:	459.1 KB 
ID:	15927

    Installed and ready to rock. Nevermind the ugly catalytic convertor.
    Click image for larger version. 

Name:	Finished Driveshaft 1.JPG 
Views:	5 
Size:	425.9 KB 
ID:	15929Click image for larger version. 

Name:	Finished Driveshaft 2.JPG 
Views:	5 
Size:	428.4 KB 
ID:	15928
    Last edited by Serendipity; 12-01-2019 at 06:11 AM.

  10. #50
    Join Date
    Nov 2010
    Location
    Beyond the Sun
    Posts
    1,295
    Step 3: It lives!

    -Battery connected and charged: Check!

    -Grounds secured: Check!

    -Harness connected to all plugs and sensors: Check!

    -ECU connected: Check!

    Let’s fire her up!


    ****. Won't start... After all that effort replacing the grounds, it seems the starter isn’t grounding through all the adapter plates and their finishes (starter to starter adapter; anodyzed, starter adapter to mounting adapter; painted, mounting adapter to bellhousing). Haha…

    All we need is one more ground...This time from the starter to the engine block.
    Click image for larger version. 

Name:	Starter Ground 1.JPG 
Views:	5 
Size:	317.4 KB 
ID:	15930Click image for larger version. 

Name:	Starter Ground 2.JPG 
Views:	5 
Size:	335.5 KB 
ID:	15931

    Started up like a champ. Listen to her purr…
    Last edited by Serendipity; 12-01-2019 at 01:41 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •